View ADM1065ASUZ_6945439.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

super sequencer and monitor adm1065 rev. d information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2004C2011 analog devices, inc. all rights reserved. features complete supervisory and sequencing solution for up to 10 supplies 10 supply fault detectors enable supervision of supplies to <0.5% accuracy at all voltages at 25c <1.0% accuracy across all voltages and temperatures 5 selectable input attenuators allow supervision of supplies to 14.4 v on vh 6 v on vp1 to vp4 (vpx) 5 dual-function inputs, vx1 to vx5 (vxx) high impedance input to supply fault detector with thresholds between 0.573 v and 1.375 v general-purpose logic input 10 programmable driver outputs, pdo1 to pdo10 (pdox) open-collector with external pull-up push/pull output driven to vddcap or vpx open collector with weak pull-up to vddcap or vpx internally charge-pumped high drive for use with external n-fet (pdo1 to pdo6 only) sequencing engine (se) implements state machine control of pdo outputs state changes conditional on input events enables complex control of boards power-up and power-down sequence control fault event handling interrupt generation on warnings watchdog function can be integrated in se program software control of sequencing through smbus device powered by the highest of vpx, vh for improved redundancy user eeprom: 256 bytes industry-standard 2-wire bus interface (smbus) guaranteed pdo low with vh, vpx = 1.2 v available in 40-lead, 6 mm 6 mm lfcsp and 48-lead, 7 mm 7 mm tqfp packages applications central office systems servers/routers multivoltage system line cards dsp/fpga supply sequencing in-circuit testing of margined supplies for more information about the adm1065 register map, refer to the an-698 application note at www.analog.com . functional block diagram 04634-001 pdo7 pdo8 pdo9 pdo10 pdognd vdd arbitrator vccp gnd vx1 vx2 vx3 vx4 vx5 vp1 vp2 vp3 vp4 vh agnd v ddcap programmable reset generators (sfds) dual- function inputs (logic inputs or sfds) sequencing engine configurable output drivers (lv capable of driving logic signals) pdo1 pdo2 pdo3 pdo4 pdo5 pdo6 sd a scl a 1 a 0 smbus interface refout refgnd vref eeprom adm1065 configurable output drivers (hv capable of driving gates of n-fet) figure 1. general description the adm1065 super sequencer? is a configurable supervisory/ sequencing device that offers a single-chip solution for supply monitoring and sequencing in multiple-supply systems. the device also provides up to 10 programmable inputs for moni- toring undervoltage faults, overvoltage faults, or out-of-window faults on up to 10 supplies. in addition, 10 programmable outputs can be used as logic enables. six of these programmable outputs can each provide up to a 12 v output for driving the gate of an n-fet that can be placed in the path of a supply. the logical core of the device is a sequencing engine. this state machine-based construction provides up to 63 different states. this design enables very flexible sequencing of the outputs based on the condition of the inputs. the adm1065 is controlled via configuration data that can be programmed into an eeprom. the whole configuration can be programmed using an intuitive gui-based software package provided by analog devices, inc.
adm1065 rev. d | page 2 of 28 table of contents features .............................................................................................. 1 ? applications....................................................................................... 1 ? functional block diagram .............................................................. 1 ? general description ......................................................................... 1 ? revision history ............................................................................... 2 ? detailed block diagram .................................................................. 3 ? specifications..................................................................................... 4 ? absolute maximum ratings............................................................ 6 ? thermal resistance ...................................................................... 6 ? esd caution.................................................................................. 6 ? pin configurations and function descriptions ........................... 7 ? typical performance characteristics ............................................. 9 ? powering the adm1065 ................................................................ 11 ? inputs................................................................................................ 12 ? supply supervision..................................................................... 12 ? programming the supply fault detectors............................... 12 ? input comparator hysteresis.................................................... 12 ? input glitch filtering ................................................................. 13 ? supply supervision with vxx inputs....................................... 13 ? vxx pins as digital inputs ........................................................ 13 ? outputs ............................................................................................ 14 ? supply sequencing through configurable output drivers ..... 14 ? default output configuration.................................................. 14 ? sequencing engine ......................................................................... 15 ? overview ..................................................................................... 15 ? warnings...................................................................................... 15 ? smbus jump (unconditional jump)........................................ 15 ? sequencing engine application example ............................... 16 ? fault and status reporting........................................................ 17 ? applications diagram .................................................................... 18 ? communicating with the adm1065........................................... 19 ? configuration download at power-up................................... 19 ? updating the configuration ..................................................... 19 ? updating the sequencing engine............................................. 20 ? internal registers........................................................................ 20 ? eeprom ..................................................................................... 20 ? serial bus interface..................................................................... 20 ? smbus protocols for ram and eeprom.............................. 23 ? write operations ........................................................................ 23 ? read operations......................................................................... 25 ? outline dimensions ....................................................................... 26 ? ordering guide .......................................................................... 26 ? revision history 6/11rev. c to rev. d changes to serial bus timing parameter in table 1.................... 4 changes to figure 3.......................................................................... 7 added exposed pad notation to outline dimensions ............. 26 changes to ordering guide .......................................................... 26 5/08rev. b to rev. c changes to table 1............................................................................ 4 changes to powering the adm1065 section ............................. 10 changes to default output configuration section ................... 13 changes to sequence detector section ....................................... 15 changes to configuration download at power-up section..... 18 changes to table 9.......................................................................... 19 changes to figure 26...................................................................... 20 changes to figure 27...................................................................... 21 changes to figure 36 and error correction section ................. 24 changes to ordering guide .......................................................... 25 7/06rev. a to rev. b changes to features.......................................................................... 1 changes to figure 1.......................................................................... 1 changes to figure 2...........................................................................3 changes to table 1.............................................................................4 changes to table 2.............................................................................6 changes to table 3.............................................................................7 inserted table 4; renumbered sequentially ..................................7 changes to programming the supply fault detectors section 11 changes to outputs section.......................................................... 14 changes to fault reporting section ............................................ 19 changes to figure 24...................................................................... 20 inserted table 9; renumbered sequentially ............................... 23 changes to ordering guide .......................................................... 28 1/05rev. 0 to rev. a. changes to specifications section...................................................3 change to absolute maximum ratings section ...........................7 change to supply sequencing through configurable output drivers section.................................................................. 14 changes to figure 24...................................................................... 18 change to table 8 ........................................................................... 28 10/04revision 0: initial version
adm1065 rev. d | page 3 of 28 detailed block diagram 04634-002 gpi signal conditioning sfd gpi signal conditioning sfd sfd sfd selectable attenuator selectable attenuator device controller osc eeprom sda scl a1 a0 smbus interface refout refgnd vref adm1065 configurable output driver (hv) pdo1 pdo2 pdognd pdo3 gnd pdo4 pdo5 pdo8 pdo9 configurable output driver (hv) pdo6 configurable output driver (lv) pdo7 configurable output driver (lv) pdo10 sequencing engine vx2 vx3 vx4 vp2 vp3 vp4 vh vp1 vx1 agnd vx5 vddcap vdd arbitrator vccp reg 5.25v charge pump figure 2.
adm1065 rev. d | page 4 of 28 specifications vh = 3.0 v to 14.4 v 1 , vpx = 3.0 v to 6.0 v 1 , t a = ?40c to +85c, unless otherwise noted. table 1. parameter min typ max unit test conditions/comments power supply arbitration vh, vpx 3.0 v minimum supply required on one of vh, vpx vpx 6.0 v maximum vddcap = 5.1 v typical vh 14.4 v vddcap = 4.75 v vddcap 2.7 4.75 5.4 v regulated ldo output c vddcap 10 f minimum recommended decoupling capacitance power supply supply current, i vh , i vpx 4.2 6 ma vddcap = 4.75 v, pdo1 to pdo10 off additional currents all pdo fet drivers on 1 ma vddcap = 4.75 v, pdo1 to pdo6 loaded with 1 a each, pdo7 to pdo10 off current available from vddcap 2 ma maximum additional load that can be drawn from all pdo pull-ups to vddcap eeprom erase current 10 ma 1 ms duration only, vddcap = 3 v supply fault detectors vh pin input impedance 52 k input attenuator error 0.05 % midrange and high range detection ranges high range 6 14.4 v midrange 2.5 6 v vpx pins input impedance 52 k input attenuator error 0.05 % low range and midrange detection ranges midrange 2.5 6 v low range 1.25 3 v ultralow range 0.573 1.375 v no input attenuation error vxx pins input impedance 1 m detection ranges ultralow range 0.573 1.375 v no input attenuation error absolute accuracy 1 % vref error + dac nonlinearity + comparator offset error + input attenuation error threshold resolution 8 bits digital glitch filter 0 s mi nimum programmable filter length 100 s maximum programmable filter length reference output reference output voltage 2.043 2.048 2.053 v no load load regulation ?0.25 mv sourcing current 0.25 mv sinking current minimum load capacitance 1 f capacitor required for decoupling, stability psrr 60 db dc
adm1065 rev. d | page 5 of 28 parameter min typ max unit test conditions/comments programmable driver outputs high voltage (charge pump) mode (pdo1 to pdo6) output impedance 500 k v oh 11 12.5 14 v i oh = 0 a 10.5 12 13.5 v i oh = 1 a i outavg 20 a 2 v < v oh < 7 v standard (digital output) mode (pdo1 to pdo10) v oh 2.4 v v pu (pull-up to vddcap or vpx) = 2.7 v, i oh = 0.5 ma 4.5 v v pu to vpx = 6.0 v, i oh = 0 ma v pu ? 0.3 v v pu 2.7 v, i oh = 0.5 ma v ol 0 0.50 v i ol = 20 ma i ol 2 20 ma maximum sink current per pdo pin i sink 2 60 ma maximum total sink for all pdo pins r pull-up 16 20 29 k internal pull-up i source (vpx) 2 2 ma current load on any vpx pull-ups, that is, total source current available through any number of pdo pull-up switches configured onto any one vpx pin three-state output leakage current 10 a v pdo = 14.4 v oscillator frequency 90 100 110 khz all on-chip time delays derived from this clock digital inputs (vxx, a0, a1) input high voltage, v ih 2.0 v maximum v in = 5.5 v input low voltage, v il 0.8 v maximum v in = 5.5 v input high current, i ih ?1 a v in = 5.5 v input low current, i il 1 a v in = 0 v input capacitance 5 pf programmable pull-down current, i pull-down 20 a vddcap = 4.75 v, t a = 25c if known logic state is required serial bus digital inputs (sda, scl) input high voltage, v ih 2.0 v input low voltage, v il 0.8 v output low voltage, v ol 2 0.4 v i out = ?3.0 ma serial bus timing 3 clock frequency, f sclk 400 khz bus free time, t buf 1.3 s start setup time, t su;sta 0.6 s stop setup time, t su;sto 0.6 s start hold time, t hd;sta 0.6 s scl low time, t low 1.3 s scl high time, t high 0.6 s scl, sda rise time, t r 300 ns scl, sda fall time, t f 300 ns data setup time, t su;dat 100 ns data hold time, t hd;dat 5 ns input low current, i il 1 a v in = 0 v sequencing engine timing state change time 10 s 1 at least one of the vh, vpx pins must be 3.0 v to maintain the device supply on vddcap. 2 specification is not production tested but is supported by characterization data at initial product release. 3 timing specifications are guaranteed by design and supported by characterization data.
adm1065 rev. d | page 6 of 28 absolute maximum ratings table 2. parameter rating voltage on vh pin 16 v voltage on vpx pins 7 v voltage on vxx pins ?0.3 v to +6.5 v voltage on a0, a1 pins ?0.3 v to +7 v voltage on refout pin 5 v voltage on vddcap, vccp pins 6.5 v voltage on pdox pins 16 v voltage on sda, scl pins 7 v voltage on gnd, agnd, pdognd, refgnd pins ?0.3 v to +0.3 v input current at any pin 5 ma package input current 20 ma maximum junction temperature (t j max) 150c storage temperature range ?65c to +150c lead temperature, soldering vapor phase, 60 sec 215c esd rating, all pins 2000 v stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. thermal resistance ja is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. table 3. thermal resistance package type ja unit 40-lead lfcsp 25 c/w 48-lead tqfp 50 c/w esd caution
adm1065 rev. d | page 7 of 28 pin configurations and function descriptions 04634-003 notes 1. nc = no connect. 2. the lfcsp has an exposed pad on the bottom. this pad is a no connect (nc). if possible, this pad should be soldered to the board for improved mechanical stability. adm1065 top view (not to scale) gnd 40 vddcap 39 nc 38 nc 37 sda 36 scl 35 a1 34 a0 33 vccp 32 pdognd 31 agnd 11 refgnd 12 nc 13 refout 14 nc 15 nc 16 nc 17 nc 18 nc 19 nc 20 vx1 1 vx2 2 vx3 3 vx4 4 vx5 5 vp1 6 vp2 7 vp3 8 vp4 9 vh 10 pdo1 30 pdo2 29 pdo3 28 pdo4 27 pdo5 26 pdo6 25 pdo7 24 pdo8 23 pdo9 22 pdo10 21 pin 1 indicator figure 3. lfcsp pin configuration 04634-004 nc = no connect nc 48 gnd 47 vddcap 46 nc 45 nc 44 sda 43 scl 42 a1 41 a0 40 vccp 39 pdognd 38 nc 37 nc 13 agnd 14 refgnd 15 nc 16 refout 17 nc 18 nc 19 nc 20 nc 21 nc 22 nc 23 nc 24 nc 1 v x1 2 v x2 3 v x3 4 v x4 5 v x5 6 v p1 7 v p2 8 v p3 9 v p4 10 vh 11 nc 12 nc 36 pdo1 35 pdo2 34 pdo3 33 pdo4 32 pdo5 31 pdo6 30 pdo7 29 pdo8 28 pdo9 27 pdo10 26 nc 25 adm1065 top view (not to scale) pin 1 indicator figure 4. tqfp pin configuration table 4. pin function descriptions pin o. lfcsp 1 tfp nemonic description 13, 15 to 20, 37, 38 1, 12, 13, 16, 18 to 25, 36, 37, 44, 45, 48 nc no connection. 1 to 5 2 to 6 vx1 to vx5 (vxx) high impedance inputs to supply fault detectors. fault thresholds can be set from 0.573 v to 1.375 v. alternatively, these pins can be used as general-purpose digital inputs. 6 to 9 7 to 10 vp1 to vp4 (vpx) low voltage inputs to supply fault detectors. three input ranges can be set by altering the input attenuation on a potential divider connected to these pins, the output of which connects to a supply fault detector. these pins allow thresholds from 2.5 v to 6.0 v, from 1.25 v to 3.00 v, and from 0.573 v to 1.375 v. 10 11 vh high voltage input to supply fault detectors. two input ranges can be set by altering the input attenuation on a potential divider connecte d to this pin, the output of which connects to a supply fault detector. this pi n allows thresholds from 6.0 v to 14.4 v and from 2.5 v to 6.0 v. 11 14 agnd 2 ground return for input attenuators. 12 15 refgnd 2 ground return for on-chip reference circuits. 14 17 refout reference output, 2.048 v. note that the ca pacitor must be connected between this pin and refgnd. a 10 f capacitor is recommended for this purpose. 21 to 30 26 to 35 pdo10 to pdo1 programmable output drivers. 31 38 pdognd 2 ground return for output drivers. 32 39 vccp central charge-pump voltage of 5.25 v. a reservoir capacitor must be connected between this pin and gnd. a 10 f capacitor is recommended for this purpose. 33 40 a0 logic input. this pin sets the seventh bit of the smbus interface address. 34 41 a1 logic input. this pin sets the sixth bit of the smbus interface address. 35 42 scl smbus clock pin. bidirectional open drain requires external resistive pull-up. 36 43 sda smbus data pin. bidirectional open drain requires external resistive pull-up.
adm1065 rev. d | page 8 of 28 pin no. lfcsp 1 tqfp description mnemonic 39 46 vddcap device supply voltage. linearly regulated from the highest of the vpx, vh pins to a typical of 4.75 v. note that the capacitor must be connected between this pin and gnd. a 10 f capacitor is recommended for this purpose. 40 47 gnd 2 supply ground. 1 note that the lfcsp has an exposed pad on the bottom. this pad is a no connect (nc). if possible, this pad should be soldered to the board for improved mechanical stability. 2 in a typical application, all ground pins are connected together.
adm1065 rev. d | page 9 of 28 typical performance characteristics 6 0 1 2 3 4 5 06 5 4 3 2 1 04634-050 v vp1 (v) v vddcap (v) figure 5. v vddcap vs. v vp1 6 0 1 2 3 4 5 01 1412108642 04634-051 v vh (v) v vddcap (v) 6 figure 6. v vddcap vs. v vh 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0123456 04634-052 v vp1 (v) i vp1 (ma) figure 7. i vp1 vs. v vp1 (vp1 as supply) 180 160 140 120 100 80 60 40 20 0 0123456 04634-053 v vp1 (v) i vp1 (a) figure 8. i vp1 vs. v vp1 (vp1 not as supply) 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 01 1412108642 04634-054 v vh (v) i vh (ma) 6 figure 9. i vh vs. v vh (vh as supply) 350 300 250 200 150 100 50 0 06 5 4 3 2 1 04634-055 v vh (v) i vh (a) figure 10. i vh vs. v vh (vh not as supply)
adm1065 rev. d | page 10 of 28 14 12 10 8 6 4 2 0 0 15.0 12.5 10.0 7.5 5.0 2.5 04634-056 i load (a) charge-pumped v pdo1 (v) figure 11. charge-pumped v pdo1 (fet drive mode) vs. i load 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 06 5 4 3 2 1 04634-057 i load (ma) v pdo1 (v) vp1 = 5v vp1 = 3v figure 12. v pdo1 (strong pull-up to vpx) vs. i load 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 06 50 40 30 20 10 04634-058 i load (a) v pdo1 (v) 0 vp1 = 5v vp1 = 3v figure 13. v pdo1 (weak pull-up to vpx) vs. i load 2.058 2.038 2.043 2.048 2.053 ?40 ?20 0 20 40 60 100 80 04634-061 temperature (c) refout (v) vp1 = 3.0v vp1 = 4.75v figure 14. refout vs. temperature
adm1065 rev. d | page 11 of 28 powering the adm1065 the adm1065 is powered from the highest voltage input on either the positive-only supply inputs (vpx) or the high voltage supply input (vh). this technique offers improved redundancy because the device is not dependent on any particular voltage rail to keep it operational. the same pins are used for supply fault detection (see the supply supervision section). a v dd arbitrator on the device chooses which supply to use. the arbitrator can be considered an oring of five low dropout regulators (ldos) together. a supply comparator chooses the highest input to provide the on-chip supply. there is minimal switching loss with this architecture (~0.2 v), resulting in the ability to power the adm1065 from a supply as low as 3.0 v. note that the supply on the vxx pins cannot be used to power the device. an external capacitor to gnd is required to decouple the on-chip supply from noise. this capacitor should be connected to the vddcap pin, as shown in figure 15 . the capacitor has another use during brownouts (momentary loss of power). under these conditions, when the input supply (vpx or vh) dips transiently below v dd , the synchronous rectifier switch immediately turns off so that it does not pull v dd down. the v dd capacitor can then act as a reservoir to keep the device active until the next highest supply takes over the powering of the device. a 10 f capacitor is recommended for this reservoir/decoupling function. the vh input pin can accommodate supplies up to 14.4 v, which allows the adm1065 to be powered using a 12 v backplane supply. in cases where this 12 v supply is hot swapped, it is recommended that the adm1065 not be connected directly to the supply. suitable precautions, such as the use of a hot swap controller, should be taken to protect the device from transients that could cause damage during hot swap events. when two or more supplies are within 100 mv of each other, the supply that first takes control of v dd keeps control. for example, if vp1 is connected to a 3.3 v supply, v dd powers up to approximately 3.1 v through vp1. if vp2 is then connected to another 3.3 v supply, vp1 still powers the device unless vp2 goes 100 mv higher than vp1. supply comparator in en out 4.75v ldo in en out 4.75v ldo in en out 4.75v ldo in en out 4.75v ldo in en out 4.75v ldo vh vp4 vp3 vp2 vp1 vddcap internal device supply 0 4634-022 figure 15. v dd arbitrator operation
adm1065 rev. d | page 12 of 28 inputs supply supervision the adm1065 has 10 programmable inputs. five of these are dedicated supply fault detectors (sfds). these dedicated inputs are called vh and vpx (vp1 to vp4) by default. the other five inputs are labeled vxx (vx1 to vx5) and have dual functionality. they can be used either as sfds, with functionality similar to vh and vpx, or as cmos-/ttl-compatible logic inputs to the device. therefore, the adm1065 can have up to 10 analog inputs, a minimum of five analog inputs and five digital inputs, or a combination thereof. if an input is used as an analog input, it cannot be used as a digital input. therefore, a configuration requiring 10 analog inputs has no available digital inputs. table 6 shows the details of each input. programming the supply fault detectors the adm1065 can have up to 10 sfds on its 10 input channels. these highly programmable reset generators enable the supervision of up to 10 supply voltages. the supplies can be as low as 0.573 v and as high as 14.4 v. the inputs can be configured to detect an undervoltage fault (the input voltage drops below a prepro- grammed value), an overvoltage fault (the input voltage rises above a preprogrammed value), or an out-of-window fault (the input voltage is outside a preprogrammed range). the thresholds can be programmed to an 8-bit resolution in registers provided in the adm1065. this translates to a voltage resolution that is dependent on the range selected. the resolution is given by step size = threshold range /255 therefore, if the high range is selected on vh, the step size can be calculated as follows: (14.4 v ? 6.0 v)/255 = 32.9 mv table 5 lists the upper and lower limits of each available range, the bottom of each range (v b ), and the range itself (v r ). table 5. voltage range limits voltage range (v) v b (v) v r (v) 0.573 to 1.375 0.573 0.802 1.25 to 3.00 1.25 1.75 2.5 to 6.0 2.5 3.5 6.0 to 14.4 6.0 8.4 the threshold value required is given by v t = ( v r n )/255 + v b where: v t is the desired threshold voltage (undervoltage or overvoltage). v r is the voltage range. n is the decimal value of the 8-bit code. v b is the bottom of the range. reversing the equation, the code for a desired threshold is given by n = 255 (v t ? v b )/ v r for example, if the user wants to set a 5 v overvoltage threshold on vp1, the code to be programmed in the ps1ovth register (as discussed in the an-698 application note at www.analog.com ) is given by n = 255 (5 ? 2.5)/3.5 therefore, n = 182 (1011 0110 or 0xb6). input comparator hysteresis the uv and ov comparators shown in figure 16 are always monitoring vpx. to avoid chatter (multiple transitions when the input is very close to the set threshold level), these comparators have digitally programmable hysteresis. the hysteresis can be programmed up to the values shown in table 6 . 04634-023 + ? + ? uv comparator vref fault type select ov comparator fault output glitch filter vpx mid low range select ultra low figure 16. supply fault detector block the hysteresis is added after a supply voltage goes out of tolerance. therefore, the user can program the amount above the undervoltage threshold to which the input must rise before an undervoltage fault is deasserted. similarly, the user can program the amount below the overvoltage threshold to which an input must fall before an overvoltage fault is deasserted. table 6. input functions, thresholds, and ranges input function voltage range (v) maximum hysteresis voltage resolution (mv) glitch filter (s) vh high voltage analog input 2.5 to 6.0 425 mv 13.7 0 to 100 6.0 to 14.4 1.02 v 32.9 0 to 100 vpx positive analog input 0.573 to 1.375 97.5 mv 3.14 0 to 100 1.25 to 3.00 212 mv 6.8 0 to 100 2.5 to 6.0 425 mv 13.7 0 to 100 vxx high-z analog input 0.573 to 1.375 97.5 mv 3.14 0 to 100 digital input 0 to 5.0 n/a n/a 0 to 100
adm1065 rev. d | page 13 of 28 the hysteresis value is given by v hyst = v r n thresh /255 where: v hyst is the desired hysteresis voltage. n thresh is the decimal value of the 5-bit hysteresis code. note that n thresh has a maximum value of 31. the maximum hysteresis for the ranges is listed in table 6 . input glitch filtering the final stage of the sfds is a glitch filter. this block provides time-domain filtering on the output of the sfd comparators, which allows the user to remove any spurious transitions such as supply bounce at turn-on. the glitch filter function is in addition to the digitally programmable hysteresis of the sfd comparators. the glitch filter timeout is programmable up to 100 s. for example, when the glitch filter timeout is 100 s, any pulse appearing on the input of the glitch filter block that is less than 100 s in duration is prevented from appearing on the output of the glitch filter block. any input pulse that is longer than 100 s appears on the output of the glitch filter block. the output is delayed with respect to the input by 100 s. the filtering process is shown in figure 17 . 04634-024 t 0 t gf t 0 t gf t 0 t gf t 0 t gf input input pulse shorter than glitch filter timeout input pulse longe r than glitch filter timeout output programmed timeout programmed timeout input output figure 17. input glitch filter function supply supervision with vxx inputs the vxx inputs have two functions. they can be used as either supply fault detectors or digital logic inputs. when selected as analog (sfd) inputs, the vxx pins have functionality that is very similar to the vh and vpx pins. the primary difference is that the vxx pins have only one input range: 0.573 v to 1.375 v. therefore, these inputs can directly supervise only the very low supplies. however, the input impedance of the vxx pins is high, allowing an external resistor divide network to be connected to the pin. thus, potentially any supply can be divided down into the input range of the vxx pin and supervised. this enables the adm1065 to monitor other supplies, such as +24 v, +48 v, and ?5 v. an additional supply supervision function is available when the vxx pins are selected as digital inputs. in this case, the analog function is available as a second detector on each of the dedi- cated analog inputs, vpx and vh. the analog function of vx1 is mapped to vp1, vx2 is mapped to vp2, and so on. vx5 is mapped to vh. in this case, these sfds can be viewed as secondary or warning sfds. the secondary sfds are fixed to the same input range as the primary sfds. they are used to indicate warning levels rather than failure levels. this allows faults and warnings to be generated on a single-supply using only one pin. for example, if vp1 is set to output a fault when a 3.3 v supply drops to 3.0 v, vx1 can be set to output a warning at 3.1 v. warning outputs are available for readback from the status registers. they are also ored together and fed into the se, allowing warnings to generate interrupts on the pdos. therefore, in this example, if the supply drops to 3.1 v, a warning is generated, and remedial action can be taken before the supply drops out of tolerance. vxx pins as digital inputs as discussed in the supply supervision with vxx inputs section, the vxx input pins on the adm1065 have dual functionality. the second function is as a digital logic input to the device. therefore, the adm1065 can be configured for up to five digital inputs. these inputs are ttl-/cmos-compatible. standard logic signals can be applied to the pins, reset from reset generators, pwrgd signals, fault flags, manual resets, and more. these signals are available as inputs to the se and, therefore, can be used to control the status of the pdos. the inputs can be configured to detect either a change in level or an edge. when configured for level detection, the output of the digital block is a buffered version of the input. when configured for edge detection, a pulse of programmable width is output from the digital block, once the logic transition is detected. the width is programmable from 0 s to 100 s. the digital blocks feature the same glitch filter function that is available on the sfds. this function enables the user to ignore spurious transitions on the inputs. for example, the filter can be used to debounce a manual reset switch. when configured as digital inputs, each vxx pin has a weak (10 a) pull-down current source available for placing the input into a known condition, even if left floating. the current source, if selected, weakly pulls the input to gnd. 04634-027 detector vxx (digital input) glitch filter vref = 1.4v to sequencing engine + ? figure 18. vxx digital input function
adm1065 rev. d | page 14 of 28 outputs supply sequencing through configurable output drivers t he data driving each of the pdos can come from one of three sources. the source can be enabled in the pdoxcfg configu- ration register (see the an-698 application note for details). s upply sequencing is achieved with the adm1065 using the programmable driver outputs (pdos) on the device as control signals for supplies. the output drivers can be used as logic enables or as fet drivers. t he data sources are as follows: ? output from the se. ? directly from the smbus. a pdo can be configured so that the smbus has direct control over it. this enables software control of the pdos. therefore, a microcontroller can be used to initiate a software power-up/power-down sequence. t he sequence in which the pdos are asserted (and, therefore, the supplies are turned on) is controlled by the sequencing engine (se). the se determines what action is taken with the pdos, based on the condition of the adm1065 inputs. therefore, the pdos can be set up to assert when the sfds are in tolerance, the correct input signals are received on the vxx digital pins, no warnings are received from any of the inputs of the device, and at other times. the pdos can be used for a variety of functions. the primary function is to provide enable signals for ldos or dc-to-dc converters that generate supplies locally on a board. the pdos can also be used to provide a pwrgd signal when all the sfds are in tolerance or a reset output if one of the sfds goes out of specification (this can be used as a status signal for a dsp, fpga, or other microcontroller). ? on-chip clock. a 100 khz clock is generated on the device. this clock can be made available on any of the pdos. it can be used, for example, to clock an external device such as an led. d efault output configuration a ll of the internal registers in an unprogrammed adm1065 device from the factory are set to 0. because of this, the pdox pins are pulled to gnd by a weak (20 k) on-chip pull-down resistor. a s the input supply to the adm1065 ramps up on vpx or vh, all pdox pins behave as follows: ? input supply = 0 v to 1.2 v. the pdos are high impedance. t he pdos can be programmed to pull up to a number of different options. the outputs can be programmed as follows: ? input supply = 1.2 v to 2.7 v. the pdos are pulled to gnd by a weak (20 k) on-chip pull-down resistor. ? supply > 2.7 v. factory programmed devices continue to pull all pdos to gnd by a weak (20 k) on-chip pull-down resistor. programmed devices download current eeprom configuration data, and the programmed setup is latched. the pdo then goes to the state demanded by the configuration. this provides a known condition for the pdos during power-up. ? open drain (allowing the user to connect an external pull- up resistor). ? open drain with weak pull-up to v dd . ? open drain with strong pull-up to v dd . ? open drain with weak pull-up to vpx. ? open drain with strong pull-up to vpx. ? strong pull-down to gnd. the internal pull-down can be overdriven with an external pull- up of suitable value tied from the pdox pin to the required pull-up voltage. the 20 k resistor must be accounted for in calculating a suitable value. for example, if pdox must be pulled up to 3.3 v, and 5 v is available as an external supply, the pull-up resistor value is given by ? internally charge-pumped high drive (12 v, pdo1 to pdo6 only). t he last option (available only on pdo1 to pdo6) allows the user to directly drive a voltage high enough to fully enhance an external n-fet, which is used to isolate, for example, a card- side voltage from a backplane supply (a pdo can sustain greater than 10.5 v into a 1 a load). the pull-down switches can also be used to drive status leds directly. 3.3 v = 5 v 20 k/( r up + 20 k) therefore, r up = (100 k ? 66 k)/3.3 v = 10 k 04634-028 pdo se data cfg4 cfg5 cfg6 smbus data clk data 10 20k 10 20k vp1 sel vp4 10 20k v dd v fet (pdo1 to pdo6 only) 20k
adm1065 rev. d | page 15 of 28 sequencing engine overview t he adm1065 sequencing engine (se) provides the user with powerful and flexible control of sequencing. the se implements a state machine control of the pdo outputs with state changes conditional on input events. se programs can enable complex control of boards such as power-up and power-down sequence control, fault event handling, and interrupt generation on warnings, among others. a watchdog function that verifies the continued operation of a processor clock can be integrated into the se program. the se can also be controlled via the smbus, giving software or firmware control of the board sequencing. t he se state machine comprises 63 state cells. each state has the following attributes: ? monitors signals indicating the status of the 10 input pins, vp1 to vp4, vh, and vx1 to vx5. ? can be entered from any other state. ? three exit routes move the state machine onto a next state: sequence detection, fault monitoring, and timeout. ? delay timers for the sequence and timeout blocks can be programmed independently, and changed with each state change. the range of timeouts is from 0 ms to 400 ms. ? output condition of the 10 pdo pins is defined and fixed within a state. ? transition from one state to the next is made in less than 20 s, which is the time needed to download a state definition from eeprom to the se. 04634-029 sequence timeout monitor fault state figure 20. state cell the adm1065 offers up to 63 state definitions. the signals monitored to indicate the status of the input pins are the outputs of the sfds. warnings the se also monitors warnings. these warnings can be generated when the adc readings violate their limit register value or when the secondary voltage monitors on vpx and vh are triggered. the warnings are ored together and are available as a single warning input to each of the three blocks that enable exiting a state. smbus jump (unconditional jump) the se can be forced to advance to the next state unconditionally. this enables the user to force the se to advance. examples of the use of this feature include moving to a margining state or debugging a sequence. the smbus jump or go-to command can be seen as another input to sequence and timeout blocks to provide an exit from each state. table 7. sample sequence state entries state sequence timeout monitor idle1 if vx1 is low, go to state idle2. idle2 if vp1 is okay, go to state en3v3. en3v3 if vp2 is okay, go to state en2v5. if vp2 is not okay after 10 ms, go to state dis3v3. if vp1 is not okay, go to state idle1. dis3v3 if vx1 is high, go to state idle1. en2v5 if vp3 is okay, go to state pwrgd. if vp3 is not okay after 20 ms, go to state dis2v5. if vp1 or vp2 is not okay, go to state fsel2. dis2v5 if vx1 is high, go to state idle1. fsel1 if vp3 is not okay, go to state dis2v5. if vp1 or vp2 is not okay, go to state fsel2. fsel2 if vp2 is not okay, go to state dis3v3. if vp1 is not okay, go to state idle1. pwrgd if vx1 is high, go to state dis2v5. if vp 1, vp2, or vp3 is not okay, go to state fsel1.
adm1065 rev. d | page 16 of 28 sequencing engine application example the application in this section demonstrates the operation of the se. figure 22 shows how the simple building block of a single se state can be used to build a power-up sequence for a three-supply system. table 8 lists the pdo outputs for each state in the same se implementation. in this system, a good 5 v supply on vp1 and the vx1 pin held low are the triggers required to start a power-up sequence. the sequence next turns on the 3.3 v supply, then the 2.5 v supply (assuming successful turn-on of the 3.3 v supply). when all three supplies have turned on correctly, the pwrgd state is entered, where the se remains until a fault occurs on one of the three supplies or until it is instructed to go through a power-down sequence by vx1 going high. faults are dealt with throughout the power-up sequence on a case- by-case basis. the following three sections (the sequence detector section, the monitoring fault detector section, and the timeout detector section) describe the individual blocks and use the sample application shown in figure 22 to demonstrate the actions of the state machine. sequence detector the sequence detector block is used to detect when a step in a sequence has been completed. it looks for one of the se inputs to change state, and is most often used as the gate for successful progress through a power-up or power-down sequence. a timer block that is included in this detector can insert delays into a power-up or power-down sequence, if required. timer delays can be set from 10 s to 400 ms. figure 21 is a block diagram of the sequence detector. 04634-032 supply fault detection logic input change or fault detection warnings force flow (unconditional jump) vp1 vx5 invert sequence detector select timer figure 21. sequence detector block diagram if a timer delay is specified, the input to the sequence detector must remain in the defined state for the duration of the timer delay. if the input changes state during the delay, the timer is reset. the sequence detector can also help to identify monitoring faults. in the sample application shown in figure 22 , the fsel1 and fsel2 states first identify which of the vp1, vp2, or vp3 pins has faulted, and then they take appropriate action. 04634-030 idle1 idle2 en3v3 dis3v3 dis2v5 pwrgd fsel1 fsel2 sequence states monitor fault states timeout states vx1 = 0 vp1 = 1 vp1 = 0 (vp1 + vp2) = 0 (vp1 + vp2 + vp3) = 0 (vp1 + vp2) = 0 vp2 = 1 vp3 = 1 vp2 = 0 vx1 = 1 vp3 = 0 vp2 = 0 vp1 = 0 vx1 = 1 vx1 = 1 10ms 20ms en2v5 figure 22. sample application flow diagram table 8. pdo outputs for each state pdo outputs idle1 idle2 en3v3 en2v5 dis3v3 dis2v5 pwrgd fsel1 fsel2 pdo1 = 3v3on 0 0 1 1 0 1 1 1 1 pdo2 = 2v5on 0 0 0 1 1 0 1 1 1 pdo3 = fault 0 0 0 0 1 1 0 1 1
adm1065 rev. d | page 17 of 28 monitoring fault detector the monitoring fault detector block is used to detect a failure on an input. the logical function implementing this is a wide or gate that can detect when an input deviates from its expected condition. the clearest demonstration of the use of this block is in the pwrgd state, where the monitor block indicates that a failure on one or more of the vp1, vp2, or vp3 inputs has occurred. no programmable delay is available in this block because the triggering of a fault condition is likely to be caused by a supply falling out of tolerance. in this situation, the device needs to react as quickly as possible. some latency occurs when moving out of this state, however, because it takes a finite amount of time (~20 s) for the state configuration to download from the eeprom into the se. figure 23 is a block diagram of the monitoring fault detector. 04634-033 supply fault detection logic input change or fault detection v p1 v x5 monitoring fault detector mask sense 1-bit fault detector fault warnings mask 1-bit fault detector fault mask sense 1-bit fault detector fault figure 23. monitoring fault detector block diagram timeout detector the timeout detector allows the user to trap a failure to ensure proper progress through a power-up or power-down sequence. in the sample application shown in figure 22 , the timeout next- state transition is from the en3v3 and en2v5 states. for the en3v3 state, the signal 3v3on is asserted on the pdo1 output pin upon entry to this state to turn on a 3.3 v supply. this supply rail is connected to the vp2 pin, and the sequence detector looks for the vp2 pin to go above its undervoltage threshold, which is set in the supply fault detector (sfd) attached to that pin. the power-up sequence progresses when this change is detected. if, however, the supply fails (perhaps due to a short circuit overloading this supply), the timeout block traps the problem. in this example, if the 3.3 v supply fails within 10 ms, the se moves to the dis3v3 state and turns off this supply by bringing pdo1 low. it also indicates that a fault has occurred by taking pdo3 high. timeout delays of 100 s to 400 ms can be programmed. fault and status reporting the adm1065 has a fault latch for recording faults. two registers, fstat1 and fstat2, are set aside for this purpose. a single bit is assigned to each input of the device, and a fault on that input sets the relevant bit. the contents of the fault register can be read out over the smbus to determine which input(s) faulted. the fault register can be enabled or disabled in each state. to latch data from one state, ensure that the fault latch is disabled in the following state. this ensures that only real faults are captured and not, for example, undervoltage conditions that may be present during a power-up or power-down sequence. the adm1065 also has a number of status registers. these include more detailed information, such as whether an under- voltage or overvoltage fault is present on a particular input. the status registers also include information on adc limit faults. note that the data in the status registers is not latched in any way and, therefore, is subject to change at any time. see the an-698 application note at www.analog.com for full details about the adm1065 registers.
adm1065 rev. d | page 18 of 28 applications diagram 04634-068 3.3v out 3.3v out vh pdo8 pdo9 system reset pdo7 pdo6 pdo2 pdo1 pdo5 pdo4 pdo3 en out dc-to-dc1 in 3.3v out 3v out 5v out 12v out en out dc-to-dc2 in 2.5v out en out dc-to-dc3 in en out ldo in 1.8v out 0.9v out 1.2v out 5v out 12v in 5v in 3v in vp1 3v out vp2 3.3v out vp3 2.5v out vp4 1.8v out vx1 1.2v out vx2 0.9v out vx3 vx4 vx5 10f vccp 10f vddcap 10f refout gnd pdo10 adm1065 signal valid pwrgd powron reset en out dc-to-dc4 in figure 24. applications diagram
adm1065 rev. d | page 19 of 28 communicating with the adm1065 co nfiguration downlo ad at power-up th e configuration of the adm1065 (undervoltage/overvoltage thresholds, glitch filter timeouts, pdo configurations, and so on) is dictated by the contents of the ram. the ram comprises digital latches that are local to each of the functions on the device. the latches are double-buffered and have two identical latches, latch a and latch b. therefore, when an update to a function occurs, the contents of latch a are updated first, and then the contents of latch b are updated with identical data. the advantages of this architecture are explained in detail in the updating the configuration section. th e two latches are volatile memory and lose their contents at power-down. therefore, the configuration in the ram must be restored at power-up by downloading the contents of the eeprom (nonvolatile memory) to the local latches. this download occurs in steps, as follows: 1. with no power applied to the device, the pdos are all high impedance. 2. when 1.2 v appears on any of the inputs connected to the vdd arbitrator (vh or vpx), the pdos are all weakly pulled to gnd with a 20 k resistor. 3. when the supply rises above the undervoltage lockout of the device (uvlo is 2.5 v), the eeprom starts to download to the ram. 4. the eeprom downloads its contents to all latch as. 5. when the contents of the eeprom are completely downloaded to the latch as, the device controller signals all latch as to download to all latch bs simultaneously, completing the configuration download. 6. at 0.5 ms after the configuration download completes, the first state definition is downloaded from the eeprom into the se. note that any attempt to communicate with the device prior to the completion of the download causes the adm1065 to issue a no acknowledge (nack). updating the configuration after power-up, with all the configuration settings loaded from the eeprom into the ram registers, the user may need to alter the configuration of functions on the adm1065, such as changing the undervoltage or overvoltage limit of an sfd, changing the fault output of an sfd, or adjusting the rise time delay of one of the pdos. the adm1065 provides several options that allow the user to update the configuration over the smbus interface. the following three options are controlled in the updcfg register. option 1 update the configuration in real time. the user writes to the ram across the smbus and the configuration is updated immediately. option 2 update the latch as without updating the latch bs. with this method, the configuration of the adm1065 remains unchanged and continues to operate in the original setup until the instruction is given to update the latch bs. option 3 change the eeprom register contents without changing the ram contents, and then download the revised eeprom contents to the ram registers. with this method, the configuration of the adm1065 remains unchanged and continues to operate in the original setup until the instruction is given to update the ram. the instruction to download from the eeprom in option 3 is also a useful way to restore the original eeprom contents if revisions to the configuration are unsatisfactory. for example, if the user needs to alter an overvoltage threshold, the ram register can be updated, as described in option 1 . however, if the user is not satisfied with the change and wants to revert to the original programmed value, the device controller can issue a command to download the eeprom contents to the ram again, as described in option 3 , restoring the adm1065 to its original configuration. the topology of the adm1065 makes this type of operation possible. the local, volatile registers (ram) are all double- buffered latches. setting bit 0 of the updcfg register to 1 leaves the double-buffered latches open at all times. if bit 0 is set to 0 when a ram write occurs across the smbus, only the first side of the double-buffered latch is written to. the user must then write a 1 to bit 1 of the updcfg register. this generates a pulse to update all the second latches at once. eeprom writes occur in a similar way. the final bit in this register can enable or disable eeprom page erasure. if this bit is set high, the contents of an eeprom page can all be set to 1. if this bit is set low, the contents of a page cannot be erased, even if the command code for page erasure is programmed across the smbus. the bit map for the updcfg register is shown in the an-698 application note at www.analog.com . a flow diagram for download at power-up and subsequent configuration updates is shown in figure 25 .
adm1065 rev. d | page 20 of 28 04634-035 power-up (v cc > 2.5v) eeprom e e p r o m l d d a t a r a m l d u p d smbus device controller latch a latch b function (ov threshold on vp1) figure 25. configuration update flow diagram updating the sequencing engine sequencing engine (se) functions are not updated in the same way as regular configuration latches. the se has its own dedicated 512-byte, nonvolatile, electrically erasable, programmable, read- only memory (eeprom) for storing state definitions, providing 63 individual states, each with a 64-bit word (one state is reserved). at power-up, the first state is loaded from the se eeprom into the engine itself. when the conditions of this state are met, the next state is loaded from the eeprom into the engine, and so on. the loading of each new state takes approximately 10 s. to alter a state, the required changes must be made directly to the eeprom. ram for each state does not exist. the relevant alterations must be made to the 64-bit word, which is then uploaded directly to the eeprom. internal registers the adm1065 contains a large number of data registers. the principal registers are the address pointer register and the configuration registers. address pointer register the address pointer register contains the address that selects one of the other internal registers. when writing to the adm1065, the first byte of data is always a register address that is written to the address pointer register. configuration registers the configuration registers provide control and configuration for various operating parameters of the adm1065. eeprom t he adm1065 has two 512-byte cells of nonvolatile eeprom from register address 0xf800 to register address 0xfbff. the eeprom is used for permanent storage of data that is not lost when the adm1065 is powered down. one eeprom cell contains the configuration data of the device; the other contains the state definitions for the se. although referred to as read-only memory, the eeprom can be written to, as well as read from, using the serial bus in exactly the same way as the other registers. t he major differences between the eeprom and other registers are as follows: ? an eeprom location must be blank before it can be written to. if it contains data, the data must first be erased. ? writing to the eeprom is slower than writing to the ram. ? writing to the eeprom should be restricted because it has a limited write/cycle life of typically 10,000 write operations, due to the usual eeprom wear-out mechanisms. t he first eeprom is split into 16 (0 to 15) pages of 32 bytes each. page 0 to page 6, starting at address 0xf800, hold the configuration data for the applications on the adm1065 (such as the sfds and pdos). these eeprom addresses are the same as the ram register addresses, prefixed by f8. page 7 is reserved. page 8 to page 15 are for customer use. data can be downloaded from the eeprom to the ram in one of the following ways: ? at power-up, when page 0 to page 6 are downloaded ? by setting bit 0 of the udownld register (0xd8), which performs a user download of page 0 to page 6 serial bus interface the adm1065 is controlled via the serial system management bus (smbus) and is connected to this bus as a slave device under the control of a master device. it takes approximately 1 ms after power-up for the adm1065 to download from its eeprom. therefore, access to the adm1065 is restricted until the download is complete. identifying the adm1065 on the smbus the adm1065 has a 7-bit serial bus slave address (see tabl e 9 ). the device is powered up with a default serial bus address. the five msbs of the address are set to 01011; the two lsbs are determined by the logical states of pin a1 and pin a0. this allows the connection of four adm1065s to one smbus. table 9. serial bus slave address a1 pin a0 pin hex address 7-bit address low low 0x58 0101100x 1 low high 0x5a 0101101x 1 high low 0x5c 0101110x 1 high high 0x5e 0101111x 1 1 x = read/write bit. the address is shown only as the first 7 msbs.
adm1065 rev. d | page 21 of 28 the device also has several identification registers (read-only) that can be read across the smbus. table 10 lists these registers with their values and functions. table 10. identification regi ster values and functions name address value function manid 0xf4 0x41 manufacturer id for analog devices revid 0xf5 0x02 silicon revision mark1 0xf6 0x00 software brand mark2 0xf7 0x00 software brand general smbus timing figure 26 , figure 27 , and figure 28 are timing diagrams for general read and write operations using the smbus. the smbus specification defines specific conditions for different types of read and write operations, which are discussed in the wr ite operations and read operations sections. the general smbus protocol operates as follows: step 1 the master initiates data transfer by establishing a start condition, defined as a high-to-low transition on the serial data-line sda, while the serial clock-line scl remains high. this indicates that a data stream follows. all slave peripherals connected to the serial bus respond to the start condition and shift in the next eight bits, consisting of a 7-bit slave address (msb first) plus an r/ w bit. this bit determines the direction of the data transfer, that is, whether data is written to or read from the slave device (0 = write, 1 = read). the peripheral whose address corresponds to the transmitted address responds by pulling the data line low during the low period before the ninth clock pulse, known as the acknowledge bit (ack), and holding it low during the high period of this clock pulse. all other devices on the bus remain idle while the selected device waits for data to be read from or written to it. if the r/ w bit is a 0, the master writes to the slave device. if the r/ w bit is a 1, the master reads from the slave device. step 2 data is sent over the serial bus in sequences of nine clock pulses: eight bits of data followed by an acknowledge bit from the slave device. data transitions on the data line must occur during the low period of the clock signal and remain stable during the high period because a low-to-high transition when the clock is high could be interpreted as a stop signal. if the operation is a write operation, the first data byte after the slave address is a command byte. this command byte tells the slave device what to expect next. it may be an instruction telling the slave device to expect a block write, or it may be a register address that tells the slave where subsequent data is to be written. because data can flow in only one direction, as defined by the r/ w bit, sending a command to a slave device during a read operation is not possible. before a read operation, it may be necessary to perform a write operation to tell the slave what sort of read operation to expect and the address from which data is to be read. step 3 when all data bytes have been read or written, stop conditions are established. in write mode, the master pulls the data line high during the 10th clock pulse to assert a stop condition. in read mode, the master device releases the sda line during the low period before the ninth clock pulse, but the slave device does not pull it low. this is known as a no acknowledge. the master then takes the data line low during the low period before the 10th clock pulse and then high during the 10th clock pulse to assert a stop condition. 04634-036 19 9 1 19 1 9 start by master ack. by slave ack. by slave ack. by slave ack. by slave frame 2 command code frame 1 slave address frame n data byte frame 3 data byte scl sda r/w stop by master scl (continued) sda (continued) d7 a0 a1 1 01 0 1 d6 d5 d4 d3 d2 d1 d0 d7 d6 d5 d4 d3 d2 d1 d0 d7 d6 d5 d4 d3 d2 d1 d0 figure 26. general smbus write timing diagram
adm1065 rev. d | page 22 of 28 9 04634-037 19 9 1 19 1 start by master ack. by slave ack. by master ack. by master no ack. frame 2 data byte frame 1 slave address frame n data byte frame 3 data byte scl sda r/w stop by master scl (continued) sda (continued) d7 a0 a1 1 01 0 1 d6 d5 d4 d3 d2 d1 d0 d7 d6 d5 d4 d3 d2 d1 d0 d7 d6 d5 d4 d3 d2 d1 d0 figure 27. general smbus read timing diagram 04634-038 scl sda ps s p t su;sto t hd;sta t su;sta t su;dat t hd;dat t hd;sta t high t buf t low t r t f figure 28. serial bus timing diagram
adm1065 rev. d | page 23 of 28 smbus protocols for ram and eeprom the adm1065 contains volatile registers (ram) and nonvolatile registers (eeprom). user ram occupies address 0x00 to address 0xdf; the eeprom occupies address 0xf800 to address 0xfbff. data can be written to and read from both the ram and the eeprom as single data bytes. data can be written only to unprogrammed eeprom locations. to write new data to a programmed location, the location contents must first be erased. eeprom erasure cannot be done at the byte level. the eeprom is arranged as 32 pages of 32 bytes each, and an entire page must be erased. p age erasure is enabled by setting bit 2 in the updcfg register (address 0x90) to 1. if this bit is not set, page erasure cannot occur, even if the command byte (0xfe) is programmed across the smbus. w rite operations t he smbus specification defines several protocols for different types of read and write operations. the following abbreviations are used in figure 29 to figure 37 : ? s = start ? p = stop ? r = read ? w = write ? a = acknowledge ? a = no acknowledge t he adm1065 uses the following smbus write protocols. send byte in a send byte operation, the master device sends a single command byte to a slave device, as follows: 1. the master device asserts a start condition on sda. 2. the master sends the 7-bit slave address followed by the write bit (low). 3. the addressed slave device asserts an acknowledge (ack) on sda. 4. the master sends a command code. 5. the slave asserts an ack on sda. 6. the master asserts a stop condition on sda and the transaction ends. in the adm1065, the send byte protocol is used for two purposes: ? t o write a register address to the ram for a subsequent single byte read from the same address or for a block read or a block write starting at that address, as shown in figure 29 . 04634-039 24 13 5 slave address ram address (0x00 to 0xdf) sw a a 6 p figure 29. setting a ram a ddress for subsequent read ? to erase a page of eeprom memory. eeprom memory can be written to only if it is unprogrammed. before writing to one or more eeprom memory locations that are already programmed, the page(s) containing those locations must first be erased. eeprom memory is erased by writing a command byte. the master sends a command code telling the slave device to erase the page. the adm1065 command code for a page erasure is 0xfe (1111 1110). note that for a page erasure to take place, the page address must be given in the previous write word transaction (see the wr ite byte/word section). in addition, bit 2 in the updcfg register (address 0x90) must be set to 1. 04634-040 24 13 slave address command byte (0xfe) sw a a 5 6 p figure 30. eeprom page erasure a s soon as the adm1065 receives the command byte, page erasure begins. the master device can send a stop command as soon as it sends the command byte. page erasure takes approximately 20 ms. if the adm1065 is accessed before erasure is complete, it responds with a no acknowledge (nack).
adm1065 rev. d | page 24 of 28 8 write byte/word in a write byte/word operation, the master device sends a command byte and one or two data bytes to the slave device, as follows: 1. the master device asserts a start condition on sda. 2. the master sends the 7-bit slave address followed by the write bit (low). 3. the addressed slave device asserts an ack on sda. 4. the master sends a command code. 5. the slave asserts an ack on sda. 6. the master sends a data byte. 7. the slave asserts an ack on sda. 8. the master sends a data byte or asserts a stop condition. 9. the slave asserts an ack on sda. 10. the master asserts a stop condition on sda to end the transaction. in the adm1065, the write byte/word protocol is used for three purposes: ? to write a single byte of data to the ram. in this case, the command byte is ram address 0x00 to ram address 0xdf, and the only data byte is the actual data, as shown in figure 31 . 04634-041 slave address ram address (0x00 to 0xdf) s w a data ap a 24 13 5 76 figure 31. single byte write to the ram ? to set up a 2-byte eeprom address for a subsequent read, write, block read, block write, or page erase. in this case, the command byte is the high byte of eeprom address 0xf8 to eeprom address 0xfb. the only data byte is the low byte of the eeprom address, as shown in figure 32 . 04634-042 slave address eeprom address high byte (0xf8 to 0xfb) sw a eeprom address low byte (0x00 to 0xff) ap a 24 13 5 7 6 8 figure 32. setting an eeprom address because a page consists of 32 bytes, only the three msbs of the address low byte are important for page erasure. the lower five bits of the eeprom address low byte specify the addresses within a page and are ignored during an erase operation. ? to write a single byte of data to the eeprom. in this case, the command byte is the high byte of eeprom address 0xf8 to eeprom address 0xfb. the first data byte is the low byte of the eeprom address, and the second data byte is the actual data, as shown in figure 33 . 04634-043 slave address eeprom address high byte (0xf8 to 0xfb) sw a eeprom address low byte (0x00 to 0xff) ap a 24 13 5 7 a 9 data 8 6 1 0 fi gure 33. single byte write to the eeprom blo ck write i n a block write operation, the master device writes a block of data to a slave device. the start address for a block write must be set previously. in the adm1065, a send byte operation sets a ram address, and a write byte/word operation sets an eeprom address, as follows: 1. the master device asserts a start condition on sda. 2. the master sends the 7-bit slave address followed by the write bit (low). 3. the addressed slave device asserts an ack on sda. 4. the master sends a command code that tells the slave device to expect a block write. the adm1065 command code for a block write is 0xfc (1111 1100). 5. the slave asserts an ack on sda. 6. the master sends a data byte that tells the slave device how many data bytes are being sent. the smbus specification allows a maximum of 32 data bytes in a block write. 7. the slave asserts an ack on sda. 8. the master sends n data bytes. 9. the slave asserts an ack on sda after each data byte. 10. the master asserts a stop condition on sda to end the transaction. 04634-044 slave address sw a 2 command 0xfc (block write) 4 13 a 5 byte count 6 a 7 a 91 0 a p a data 1 8 data n data 2 fi gure 34. block write to the eeprom or ram unlike some eeprom devices that limit block writes to within a page boundary, there is no limitation on the start address when performing a block write to eeprom, except when ? there must be at least n locations from the start address to the highest eeprom address (0xfbff) to avoid writing to invalid addresses. ? an address crosses a page boundary. in this case, both pages must be erased before programming. note that the adm1065 features a clock extend function for writes to the eeprom. programming an eeprom byte takes approxi- mately 250 s, which limits the smbus clock for repeated or block write operations. the adm1065 pulls scl low and extends the clock pulse when it cannot accept any more data.
adm1065 rev. d | page 25 of 28 6 9. the adm1065 sends a byte-count data byte that tells the master how many data bytes to expect. the adm1065 always returns 32 data bytes (0x20), which is the maximum allowed by the smbus version 1.1 specification. read operations th e adm1065 uses the following smbus read protocols. re ceive byte 10. the master asserts an ack on sda. in a receive byte operation, the master device receives a single byte from a slave device, as follows: 11. the master receives 32 data bytes. 12. the master asserts an ack on sda after each data byte. 1. the master device asserts a start condition on sda. 13. the master asserts a stop condition on sda to end the transaction. 2. the master sends the 7-bit slave address followed by the read bit (high). 3. the addressed slave device asserts an ack on sda. 04634-046 slave address sw a 2 command 0xfd (block read) 4 13 a 5 s 6 slave address 7 byte count 91011 a ra 8 data 1 data 32 12 a 13 p a 4. the master receives a data byte. 5. the master asserts a nack on sda. 6. the master asserts a stop condition on sda, and the transaction ends. in the adm1065, the receive byte protocol is used to read a single byte of data from a ram or eeprom location whose address has previously been set by a send byte or write byte/word operation, as shown in figure 35 . fi gure 36. block read from the eeprom or ram err or correction the adm1065 provides the option of issuing a packet error correction (pec) byte after a write to the ram, a write to the eeprom, a block write to the ram/eeprom, or a block read from the ram/ eeprom. this option enables the user to verify that the data received by or sent from the adm1065 is correct. the pec byte is an optional byte sent after the last data byte is written to or read from the adm1065. the protocol is the same as a block read for step 1 to step 12 and then proceeds as follows: 04634-045 23 14 5 slave address s r data p a a fi gure 35. single byte read from the eeprom or ram bl ock read in a block read operation, the master device reads a block of data from a slave device. the start address for a block read must have been set previously. in the adm1065, this is done by a send byte operation to set a ram address, or a write byte/word operation to set an eeprom address. the block read operation itself consists of a send byte operation that sends a block read command to the slave, immediately followed by a repeated start and a read operation that reads out multiple data bytes, as follows: 13. the adm1065 issues a pec byte to the master. the master checks the pec byte and issues another block read, if the pec byte is incorrect. 14. a nack is generated after the pec byte to signal the end of the read. 15. the master asserts a stop condition on sda to end the transaction. 1. the master device asserts a start condition on sda. 2. the master sends the 7-bit slave address followed by the write bit (low). note that the pec byte is calculated using crc-8. the frame check sequence (fcs) conforms to crc-8 by the polynomial 3. the addressed slave device asserts an ack on sda. c ( x ) = x 8 + x 2 + x 1 + 1 4. the master sends a command code that tells the slave device to expect a block read. the adm1065 command code for a block read is 0xfd (1111 1101). see the smbus version 1.1 specification for details. an example of a block read with the optional pec byte is shown in figure 37 . 5. the slave asserts ack on sda. 6. the master asserts a repeat start condition on sda. 04634-047 slave address sw a 2 command 0xfd (block read) 4 13 a 5 s 6 slave address 7 byte count 910 12 11 a ra 8 data 1 data 32 a 13 pec 14 a 15 p a 7. the master sends the 7-bit slave address followed by the read bit (high). 8. the slave asserts an ack on sda. figure 37. block read from the eeprom or ram with pec
adm1065 rev. d | page 26 of 28 outline dimensions 1 40 10 11 31 30 21 20 4.25 4.10 sq 3.95 top view 6.00 bsc sq pin 1 indicator 5.75 bsc sq 12 max 0.30 0.23 0.18 0.20 ref seating plane 1.00 0.85 0.80 0.05 max 0.02 nom coplanarity 0.08 0.80 max 0.65 typ 4.50 ref 0.50 0.40 0.30 0.50 bsc pin 1 indicator 0.60 max 0.60 max 0.25 min exposed pad (bot tom view) compliant to jedec standards mo-220-vjjd-2 072108-a for proper connection of the exposed pad, refer to the pin configuration and function descriptions section of this data sheet. figure 38. 40-lead lead frame chip scale package [lfcsp_vq] 6 mm 6 mm body, very thin quad (cp-40-1) dimensions shown in millimeters compliant to jedec standards ms-026abc 0.50 bsc lead pitch 0.27 0.22 0.17 9.00 bsc sq 7.00 bsc sq 1.20 max top view (pins down) 1 12 13 25 24 36 37 48 0.75 0.60 0.45 pin 1 view a 1.05 1.00 0.95 0.20 0.09 0.08 max coplanarity seating plane 0 min 7 3.5 0 0.15 0.05 view a rotated 90 ccw figure 39. 48-lead thin plastic quad flat package [tqfp] (su-48) dimensions shown in millimeters ordering guide model 1 temperature range package description package option adm1065acpz ?40c to +85c 40-lead lfcsp_vq cp-40-1 ADM1065ASUZ ?40c to +85c 48-lead tqfp su-48 eval-adm1065tqebz evaluation kit (tqfp version) 1 z = rohs compliant part.
adm1065 rev. d | page 27 of 28 notes
adm1065 rev. d | page 28 of 28 notes ?2004C2011 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. d04634-0-6/11(d)

▲Up To Search▲

Price & Availability of ADM1065ASUZ

	To Download ADM1065ASUZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .